Skip to main content

How To Install A Bathroom Vanity Top

how to install a bathroom vanity top

Do you want to install a bathroom vanity top? If you feel difficulty, we will show you some materials as well as the steps to install a bathroom vanity. Just follow these steps:

Step 1

Measure the base of the vanity with a tape measure and write down the size. Buy your new owner compliance with this measure. Vanity top you select will depend on the space accessible and your taste. Some sink bowl vanity tops have a built in it, while others have discounted appetizers, ready to receive your choice of the sink bowl.

Step 2

Turn off the main water supply to the bathroom.

Step 3

Separate the exhaust pipe from the sink unit using a key pipeline. Then disconnect the supply line from the existing faucet assembly on the sink using the adjustable wrench.

Step 4

Reach the base of the vanity and use a screwdriver to remove the retaining clip that holds the top of rias in place. Lift the lid of rias long from the base of the sink and set it aside.

Step 5

Check the exhaust pipe and channel the water supply for damage. Replace them if necessary before you start installing a new vanity unit.

Step 6

Place a level on the top edge of the base of the vanity and check that the level from side to side and front to back. Place shims under the base makeup as needed to make the level of the unit. Cut the excess shims using utility knife so that it is even with the side of the base.

Step 7

Place the top part of vanity and concentrated it was. Secure the top to the base using the screwdriver and the hardware that came with the dresser. Install the new faucet Assembly on top of rias after factory instructions for the brand and model that you are using.

Step 8

Connect the water supply line to the new faucet Assembly and tighten the fitting with an adjustable wrench. Connect the tailpiece on the sink into the exhaust pipe and tighten the locking collar using the adjustable wrench.

Step 9

Place a bead of caulk around the top edge of the vanity using the gun. If the top of the bathroom sinks you have separate sink bowl, put a dot in the enclosure around the side of the pan of the tub too. It will prevent water leaking onto his dressing table and ruin it.

Step 10

Turn on the water supply. Run water into the bowl of the sink and check sewer pipes and funnels the water supply to leakage.

 

How To Install A Bathroom Vanity

how to install a bathroom vanityAlong with the kitchen, the bathroom offers the best returns over the dollars invested in renovations. And one of the easiest ways to update the look of your bathroom is to replace the dressing table, table, sink, and faucet with new units that look clean. For a few hundred dollars you can make your bathroom look like a million dollars.

Step 1: Locate Wall Studs

Vanity you should cling firmly on wall studs, so the first step is to find the position of the buttons were on the wall behind the dresser.

Step 2: Prepare to Attach a Vanity

Mark the height of the top of the vanity base cabinets on the wall of the back (as well as the side walls if you have the installation angle).

Step 3: Preparing the Filler Strip (if necessary)

If the cabinet positioned on the side walls are the only remaining gaps to be filled, you have to measure and cut out a narrow filler strip to fill this gap, as shown here. This may involve the formation of a filler strip to fit around the sockets or pieces of tile at the bottom of the cabinet.

Step 4: Create and Install a Filler Strip

Cut strips of filler with a length and width of the overall gap between frame and cabinet side walls. Some vanity kits may come with a filler strip made of the same material as the face frame of the cabinet.

Step 5: Tighten the Side of the Vanity to the Wall Next

Although this step sometimes omitted, we recommend you anchor the side dresser to the side walls, as well as secure the cabinet to the back wall.

Step 6: Install the Vanity Top

If the sink is separated from the table and not an integral part, attach it to the table before placing a table on the dressing table.

Also, attach the faucet and drain fittings. It is much easier to install these components in a separate table rather than doing it after the meal is mounted.

Step 7: Connect the Pipes

After assembling the desk installed, hook the supply of tap water. How this done will depend on your style and Your faucet manufacturers, but primarily involves connecting the flexible supply tubing to run from the valve cover onto the tailpieces at the faucet.

Step 8: Install the Backsplash

Employ a bead of silicone sealant/asleep in a circular pattern at the end of the backsplash. Then, touch the backsplash inside place securely on the wall.

Step 9: Enjoy Your Vanity

After the vanity, you fully installed, back off a step and enjoy your hard work!

 

How To Install Bathroom Vanity

how to install bathroom vanityOne of the rooms in the House that has the critical function is the bathroom. Activities cleaned up at this place often has also become a form of refreshment lightning to start the day or even as relaxation in the end it. An integral part of this training is cosmetic activities themselves.

Has it ever occurred to you to bring to mind grooming station or area of the vanity in the bathroom? There is an advantage if you can allocate a plot of part of the toilet to be a dressing area. Here are some tips for installing a vanity in the bathroom:

Vanity Area

Consider who will be using the space. If you live with a partner and share a bathroom, you can create two dressing regions to make it more personal. But if spacious bathroom does not allow, you can investigate by presenting cabinet or dressing table with two storage areas.

Vanity Type

There are two types of the dressing table, i.e., the kind of legs and no legs. Legged type will make the room look more spacious. If you want to display new impression, choose dressers that have walls. Meanwhile, Dresser without foot provides a storage cabinet.

How to Storage

Make sure make-up products and treatments routinely used placed on the dressers for easy reach. This will make You more efficient use of time. Do not put the various packaging products that lack functioning on top of tables, or in the storage cabinet because it will narrow down Your vanity. Provide a unique space in the dresser for electric-powered tools.

Lighting

Layout lighting obviously played an essential role in your cosmetic activities. You should consider the layout-layout of the point of illumination in the dressing area in order not to bother by shadows lighting results. Any light intensity needs to find. Should be pretty obvious but not untune the eye.

Decorating Styles

In addition to functionality, you also need to consider the aesthetic aspect. Keep your vanity area design blends in with the overall style of the bathroom. The personal touch is also a good thing for your dressing area was presented.

 

You may also like

Leave a Reply